Exterior · Parts

Exterior door sizes for manufactured homes

Common manufactured home exterior door sizes, how to measure the opening, outswing versus inswing, and the HUD clear-opening rule.

· About 8 min read

Part
Exterior door
Category
Exterior

Order a door that matches the hole

Separate the legal clear opening from the catalog size, write down swing and hinge hand, and buy from the seller’s measuring rules.

  1. Do not remove the only good exitThe home needs two exterior doors, remote from each other. Replace a bad door. Do not close the opening up and call it finished.
  2. Write down swing and handOutswing, inswing, or a combination door with a storm panel. Stand outside to call the hinge side left or right.
  3. Measure slab, jamb, and framingRecord all three. A single number is how the wrong door gets shipped.
  4. Match the seller’s definition of sizeAsk whether their 34 by 76 is the rough opening or the slab. Order only after that answer matches your measurements.
  5. Check wall thickness on combination doorsAn inswing-plus-storm unit includes a jamb. Older metal-sided homes are often near 4 inches. Many newer walls are thicker.
  6. Plan on a safety check for outswing doorsOutswing doors, including storm and screen doors, need a safety door check so the wind cannot take the door. Locks have to open from the inside without a key.

The door on a manufactured home is a part you can measure, and it is still the part people order wrong. The usual mistake is to buy a house door, or to measure the slab when the seller wanted the hole in the wall. Freight then costs real money to send the wrong door back.

People use “mobile home” for the whole group of houses. Under the federal rules, a mobile home was built before June 15, 1976, and a manufactured home was built to the HUD Code after that. Older homes are where the odd heights show up. Newer homes are where an 80 inch door starts to appear. Neither date replaces a tape measure.

The HUD size is a clear opening, not a catalog size

Exterior swinging doors in a manufactured home have to provide a clear opening of at least 28 inches wide by 74 inches high. At least one egress door has to provide a clear opening of at least 32 inches by 74 inches. Seals and stops may reduce the other doors by up to an inch, but they may not reduce that main egress opening. Sliding glass doors have their own minimum, 28 by 72 clear. All of that is 24 CFR 3280.105(b).

Clear opening is the hole you walk through with the door open. It is smaller than the catalog call size. A “32 by 76” listing is not a 32 by 76 clear opening. You are filling the framed hole and keeping a legal exit, not matching the call size to the minimum.

The same rule requires at least two exterior doors, remote from each other, not behind a lockable interior door. One exit has to be within 35 feet of each bedroom door. Do not cover a door opening with siding because the new door was expensive. Swinging doors are built to the standard that section cites, 24 CFR 3280.405. Order a door sold for this opening.

Sizes you will actually see for sale

Sellers stock a short list. Widths of 30, 32, 34, and 36 inches show up constantly, most often with a height of 76 inches. Heights of 80 inches show up on newer homes. Heights around 72 inches show up in supplier guides as something they still get asked for on older homes, and those are harder to find.

Sellers do not agree on a single “standard.” Complete Mobile Home Supply calls a 34 by 76 diamond door its most common size. An MCM retailer guide calls 32 by 76 the usual post-1980 size and mentions 72 inch heights on older homes. Lakeway Supply lists 32, 34, and 36 by 76, plus some 80 inch heights. All of that can be true of different stock. Verify the row against your opening.

Call size you will see What sellers say about it What you should do
30 by 76 inches Shows up on secondary doors Measure. Do not assume the back door matches the front.
32 by 76 inches Very common. Some guides call it the usual post-1980 size. Match the seller’s definition of “32 by 76.”
34 by 76 inches Very common. At least one seller calls it their most-sold size. Same. Measure before you trust the slogan.
36 by 76 inches Wider openings, including some front doors on larger homes Confirm width in more than one place. Openings are not always square.
About 80 inches tall Newer homes, closer to a site-built height Still confirm swing, jamb, and rough opening.
About 72 inches tall Some older homes Harder to source. Measure before you tear the old door out.

A Mobile Home Parts Store listing for a 32 by 76 blank outswing door says the door is manufactured to comply with HUD standard 3280.405, and it tells you the size is a rough opening. That is one product, not a complete catalog. Fulton MHP is another manufactured-home parts counter if you want a second price. Stock changes.

Outswing, inswing, and the combination door

Many of these doors swing out. Newer homes often have an inswing front door, sometimes with a storm door or a combination unit that includes both. An inswing door in an outswing frame will not land on the threshold. If the door opens toward you when you stand outside, it is an outswing.

Combination doors need the jamb depth, which follows the wall. A Mobile Home Outfitters guide says earlier metal-sided walls were often about 4 inches and many later walls are closer to 6 or 6½. Their combination doors, they say, use a 4 inch jamb. Ask the seller you are actually buying from. Window style, blank or diamond or a slider, is the choice you make after the hole, the swing, and the hand are settled.

Measure it the way that seller measures it

Suppliers do not use one method, and pretending they do is how the comment sections get long.

Mobile Home Outfitters says ignore the flange and measure the framed opening, stud to stud and sill to header. Measuring the slab, they say, is the usual mistake.

Mobile Home Parts Store instead says: door closed, stand inside, measure between the jambs and from the top of the jamb to the floor. Their example turns 33½ by 75½ into a 34 by 76 order. Lakeway, for an outswing, says stand outside and measure the slab only.

Write down all three and label them:

  1. Slab width and height, door only.
  2. Inside jamb to jamb, and top of jamb to floor, door closed.
  3. Stud to stud and sill to header, if the trim is off or the old door is already out.

Then ask the seller which of those three their call size uses. A patient parts counter would rather answer that than ship a door twice. If the opening is out of square, send the smallest width and the smallest height, and say that it is out of square.

Slab only Rough opening The door itself The hole in the wall
Write down both. Sellers do not agree on which one their catalog size means.

Hinge hand, for these outswing doors, is called from outside. Left hinges are a left-hand door. Right hinges are a right-hand door. House-door catalogs sometimes name the hand from the inside. Use the manufactured-home seller’s diagram.

Locks, closers, and the wind

Every swinging exterior door other than a screen or storm door needs a key-operated lock with a deadlocking latch, or a key-operated deadbolt with a passage latch. You must be able to open it from the inside without a key. That is 24 CFR 3280.105(b)(3). A double-cylinder deadbolt, the kind that needs a key on the inside, does not meet that sentence.

Outswing doors, including storm doors and screen doors, need a safety door check. That is the closer, chain, or wind device that keeps the door from becoming a sail. The cite is 24 CFR 3280.105(b)(4). A safety chain or closer is an ordinary hardware item. The door itself is the part to buy from a manufactured-home supplier.

Florida, freight, and the threshold

In Florida the data plate states the wind zone. It does not state the door size. The threshold has to shed water. A door leak is a common start to a soft floor just inside the entry. Skirting does not fix a bad threshold.

One national supplier notes that freight on a single door can cost as much as the door. Compare a delivered price from Mobile Home Parts Store or Fulton MHP with a local counter. Leave the old door up until the new one is on site and checked against the opening.

Questions people ask

What is the standard mobile home exterior door size?

There isn’t one size. Catalogs are full of 30, 32, 34, and 36 inch widths at 76 inches tall, and newer homes often use an 80 inch height. Sellers disagree about which of those is the most common. Measure the opening and follow that seller’s chart. Verify the size for your home.

How do I measure a manufactured home door?

Write down three numbers: the door slab, the inside of the jambs with the door closed, and the framed rough opening if you can see the studs. Then use the measuring instructions for the exact door you are buying. One seller’s 32 by 76 is a rough-opening size. Another seller tells you to measure the slab.

Will a regular 80 inch prehung door from a home center fit?

Often no. Many manufactured homes were built around a shorter door and a different wall thickness, and a lot of the original doors swing out. A site-built inswing door in an outswing opening will not seal on the threshold. Measure height, width, swing, and wall thickness before you demo the old door.

Which way should the hinges be?

For a manufactured-home outswing door, stand outside. Hinges on the left are a left-hand door. Hinges on the right are a right-hand door. Residential catalogs sometimes use the opposite convention, so use the picture on the manufactured-home listing, not a house-door chart.

Sources

  1. 24 CFR 3280.105, exit facilities and exterior doors — eCFR
  2. Mobile Home Parts Store, 32 by 76 blank outswing door and measuring note — Mobile Home Parts Store
  3. How to measure an outswing mobile home door — Lakeway Supply
  4. Single outswing doors, including a 34 by 76 product description — Complete Mobile Home Supply
  5. Rough opening measurement guide — Mobile Home Outfitters
  6. Sizing notes from a manufactured-home retailer — MCM Homes