Exterior · Parts

Skirting for a manufactured home: options and what it costs

Vinyl, metal, and masonry skirting, the HUD rules for vents and access when you skirt a home, and how to compare cost without a fake price.

· About 7 min read

Part
Skirting
Category
Exterior

Plan skirting before you buy panels

Measure the perimeter and the height, choose a material, and leave legal vents and a real access door.

  1. Read the lease and the data platePark rules often name the color and the material. The data plate names the wind zone. Neither one is printed on a panel.
  2. Measure perimeter and height in several placesThe ground is rarely level. Price the tall side, not the short side. Count corners, the access door, and every place a pipe has to pass through.
  3. Pick a material for the climateVinyl is the usual default. Wood within 6 inches of the soil has to be treated or naturally durable. Metal near salt air needs a finish that will not rust through.
  4. Do the vent mathNet free area, two opposite sides, as high as practical, with a cover that keeps rodents out. A solid skirt with no vents traps moisture.
  5. Leave an access opening at the utilitiesAt least 18 inches wide, 24 inches high, and at least 3 square feet, where you can reach the water, sewer, and electrical connections.
  6. Route vents and drains through the skirtDryer vents and combustion air go outside. Heater and air-conditioner drains should not dump into the crawl space.

Skirting closes the space under a manufactured home. It is a weather skirt, a pest barrier, and a finished edge. It is not the anchor system, and it is not insulation by itself. Owners shop it as a weekend project because the panels look simple. The part that gets skipped is the vent math, the access door, and the drains that are supposed to end outside the skirt.

People call these houses mobile homes. In the rules, a mobile home was built before June 15, 1976, and a manufactured home was built to the HUD Code on or after that date. The installation rules below are the HUD installation standard, 24 CFR part 3285. An older home can still be skirted to the same idea: keep water moving away, let the crawl space breathe, and do not give animals a free porch.

What the rules actually require

Skirting is optional in the federal text and mandatory in a lot of leases. 24 CFR 3285.504 says skirting, if used, must be weather-resistant. It must not trap water behind the siding or stop the siding from expanding. Wood within 6 inches of the ground must be pressure-treated for ground contact, or naturally decay-resistant. Do not caulk the top rail solid to vinyl siding. The siding has to move, and a dam at the bottom course rots the wall from the back.

Once the skirt is on, 24 CFR 3285.505 sets the crawlspace rules:

  • Net vent area at least 1 square foot for every 150 square feet of floor area.
  • That can drop to 1 square foot per 1,500 square feet if a uniform 6-mil polyethylene sheet, or another acceptable vapor retarder, covers the ground under the entire floor.
  • Vents as high as practical, on at least two opposite sides, so air can cross.
  • Openings covered with a corrosion-resistant, weather-resistant perforated covering that keeps rodents out. In freezing climates the covers also have to be adjustable.
  • An access opening at least 18 inches wide and 24 inches high, and at least 3 square feet, located so utility connections under the home can be reached. Eighteen by twenty-four is 3 square feet exactly, so a smaller door fails even if it looks “close.”
  • Dryer vents and combustion-air inlets pass through the skirting to the outside. Water from the furnace, air conditioner, or water heater is directed away from under the home.

That number is net free area, the holes, not the face of a vinyl panel. Use the figure the maker prints.

Example math, not your floor area: 840 square feet divided by 150 is 5.6, so you need at least that much net opening, split onto opposite sides. With a full ground vapor retarder, the same floor divided by 1,500 falls under 1 square foot, still crossed and still rodent-proof. Measure your own floor. A solid skirt is how a soft floor starts from below. A water heater drain that ends under the skirt breaks the same rule.

Materials, in the order people actually buy them

Vinyl in a top rail and a ground track. The common system. A broken panel slides out. Sun and string trimmers make cheap vinyl brittle, and a loose track lets wind take the panel. Everlock sells optional windguard rods. Those rods are a product, not a count written into the code. Fasten the track the way the maker says.

Textured stone or brick patterns. Same rails, usually a higher panel price. The vent math does not change.

Metal. Tougher against a trimmer. Near salt air it needs a real finish. Bare steel that will be “painted later” rusts.

Fiber cement. Stiffer, and it wants paint. A reasonable step when a park rejects plain vinyl, if the top joint does not trap water.

Masonry. The most permanent look and usually the highest cost, because of the base. A block wall is still not a tie-down.

Wood and lattice. Wood within 6 inches of soil has to be treated or naturally durable. Open lattice rarely keeps rodents out, and many parks will not accept it as a finished skirt.

Material Relative material cost What usually goes wrong
Plain vinyl Usually the lowest of the durable options Brittle in sun, cracked by trimmers, panels leave in wind if the track is loose
Textured vinyl or faux stone Higher than plain vinyl Same fastening issues, plus a higher bill if a matching panel is discontinued
Metal Often a step up from vinyl Rust near the coast if the finish is wrong; sharp edges at the access door
Fiber cement Middle to high, once painted and fastened Paint neglect, and water trapped at the top rail
Masonry Usually the highest Cost, drainage, and the false belief that the wall anchors the home
Untreated wood or lattice Cheap at first Rot, termites, and a crawl space that is not really closed

“Usually” is doing real work in that table. It is an order of magnitude conversation, not a bid. Verify current prices with two suppliers and, if you are not installing it, two installers.

How to think about cost without a made-up average

Price the perimeter in linear feet and the height of the tall side. Corners, the access door, vents, tearing off the old skirt, and leveling soil are separate lines. Ask for the split. A single “skirting” number is hard to compare.

Mobile Home Parts Store and Fulton MHP can price a rail kit for the height you measured. A local yard may beat them after freight. An Amazon search for vinyl skirting shows panel prices. Check height, track, and whether vents are in the box.

Labor dominates masonry. On vinyl, a bad grade or a skirt wired to the frame is what blows the labor line. Fix standing water before you hide it. Many Florida parks name the color in the lease. A rejected color is the expensive cheap panel.

Florida wind, moisture, and the thing that actually holds the home

The National Weather Service puts the Atlantic hurricane season at June 1 through November 30. That is when a loose skirt becomes debris. Fasten the rails, replace brittle panels before the season, and look at the anchors while the access door is open. The data plate states the wind zone, including a coastal warning. Skirting does not upgrade that zone.

A crawl space with no vents, or with a torn belly, feeds a soft floor. The reduced vent allowance counts only when the vapor retarder covers the whole floor area. Do not bury the bottom track in mulch. Do not skirt over a combustion-air opening or dump a dryer duct underneath. Put the access door on the utility side. You will be back under there.

Questions people ask

Does HUD require skirting on a manufactured home?

The installation standard talks about skirting if you use it. It does not say every home must have skirting. Once you install it, the material, the way it is fastened, the vents, and the access opening have to meet 24 CFR 3285.504 and 3285.505. A park lease or a local rule can require skirting even when the federal text does not.

How much vent area does skirted skirting need?

At least one square foot of net vent opening for every 150 square feet of floor area, on at least two opposite sides. If a complete ground vapor retarder is installed, the minimum drops to one square foot per 1,500 square feet of floor. Use the net free area the vent maker prints, not the size of the whole panel. Verify the floor area of your home.

What skirting costs the least?

Plain vinyl panels are usually the lowest material cost among the options that last. Masonry is usually the highest, because of the footing and the labor. There is no honest national price. Price your own perimeter and panel height, and get the materials and the labor quoted separately.

Will skirting anchor the home in a hurricane?

No. Tie-downs and the foundation system hold the home. Skirting only closes the crawl space. In high wind, lightweight panels can blow out. That is a reason to fasten the rails and to check the anchors, not a reason to build a skirt and call the home tied down.

Sources

  1. 24 CFR 3285.504, skirting — eCFR
  2. 24 CFR 3285.505, crawlspace ventilation — eCFR
  3. Everlock vinyl skirting parts, including windguard rods — Everlock Systems
  4. National Weather Service hurricane safety page, season dates — National Weather Service