Heating and cooling · Parts
Furnace filter sizes for Coleman, Intertherm, and Miller
Find the filter for a Coleman, Intertherm, or Miller mobile home furnace. Catalog sizes, where the filter sits, and how to measure yours.
- Part
- Furnace filter
- Category
- Heating and cooling
Identify the filter without guessing from the logo
The brand on the furnace is a starting point. The pad in the door, and the model number, decide the part.
- Turn the power offSwitch the furnace off at the breaker before you open the blower door. The blower can start on a call for heat or cooling.
- Open the furnace doorOn many downflow furnaces the filter is a thin foam or fiber pad clipped to the inside of that door, not in a ceiling return.
- Measure the padThickness, then the two sides. Write the numbers inside the closet when you are done. A quarter inch of foam is common. Do not assume it.
- Copy the model numberThe rating plate is often on the front panel or just inside it. A parts counter can use the full model. A photo of the plate is better than a partial number.
- Match a catalog only after you measureUse the table on this page as a list of pads that exist, not as the size of your furnace.
- Keep the return path openA filter that is sucked tight against a closed-off return is the same problem as a filter that is too dense. Doors to bedrooms need a path for air back to the furnace.
The filter in a manufactured home furnace is the part people try to buy at a hardware store, and the part the hardware store often does not stock. Coleman, Intertherm, and Miller downflow furnaces were built to sit in a closet and blow air down into the belly ducts. On a great many of them, the filter is a thin pad on the inside of the furnace door, held by wire retainers. It is not the 16 by 25 by 1 inch pleated panel in the seasonal aisle.
The logo on the cabinet is not a size. Coleman and Evcon furnaces have been sold under the York and Johnson Controls family of brands for years. Intertherm and Miller were Nordyne brands, later part of Nortek. The same name stayed on the door while the filter opening changed. Two “Miller” furnaces in two homes on the same street can take different pads. Verify the size for your home by measuring the pad that is in it.
Where the filter actually is
These furnaces are usually downflow: supply air goes into the belly, and return air comes to the cabinet. On many of them the filter is foam, or a coarse hoghair pad, clipped to the inside of the front door. It is thin because it lives in the door. Some homes also have a thicker filter at a grille. If you find both, you may have more resistance than the furnace was listed with. Use the one the manual calls for.
The federal text does not publish a filter size. 24 CFR 3280.707(a) says the appliance has to be listed. The filter is part of that listing. The home’s data plate names the original furnace. A later replacement will not match that line. Read the plate on the furnace in the closet. A parts newsletter shows common plate locations and notes that the spot moves with the year. Photograph the whole plate.
Sizes parts sellers actually list
These rows are catalog listings, not a complete chart and not a promise for your model. Marketplace ads sometimes claim one pad fits both a Coleman part number and a Nordyne part number even when the published dimensions differ. If a listing disagrees with the pad you measured, believe the pad.
| What is being sold | Size on that listing | Where the seller says it fits | Source |
|---|---|---|---|
| Foam filter, Nordyne-style part 669073. A CMF exploded view calls the filter F-10. | 16 by 26 inches | Dean’s lists it for Miller furnace series including CMF, MOC, MGC, AGC, and AGB | Dean’s Mobile Home Supply; CMF diagram |
| Coleman/Evcon foam, part 7660-3401, also sold as Source 1 number S1-7660-3401 | 1/4 by 19 by 36 inches | Described as fitting a Coleman Presidential II furnace door, mounted on the built-in retainers. Sellers say it can be trimmed. | HSMHS; HVAC Parts Store |
A 16 by 26 pad and a 19 by 36 pad are not interchangeable. Trim a foam pad down if the seller says that pad is meant to be cut and you are only taking off a small amount. Do not stretch a small pad across a large door and call it filtered. Gaps at the retainer pull dust around the pad and into the blower.
Hoghair is the other material you may find: a coarse, springy pad, often gray or green, sometimes sitting in a return opening rather than on the door. Measure it the same way. There is no reason to memorize a hoghair chart you cannot check against the pad in your hand.
Larger foam pads, including sizes other than the two rows above, are sold for other furnaces. If neither row matches your measurement, take the numbers to a manufactured-home parts counter instead of forcing a house filter into the door.
Why a pleated filter is often the wrong substitute
A one-inch pleated filter resists air more than a quarter-inch foam sheet. These closet furnaces were listed with a low-resistance pad. A dense pleated filter can make the furnace run hot or short-cycle, and in cooling season a starved coil can freeze. If the manual calls for a pleated filter of a stated size, use that size. Do not raise the MERV for its own sake. If the furnace came with foam, replace it with foam of the same size, and let a washed pad dry before it goes back. Write the size inside the closet door.
A safe way to measure
- Turn the furnace breaker off. Confirm the blower is not running.
- Open the closet, then the furnace door. If the door holds the filter, lay the door down so the pad stays put until you are ready.
- Release the retainers. Note which way they face so you can put them back.
- Measure thickness first, then both sides of the pad. If the pad is gone, measure the opening inside the retainers, not the outside of the door.
- Vacuum the loose dust you can reach without taking the blower wheel apart. Do not bend the fan blades to get a shop vacuum closer.
- Put the clean or new pad fully behind the retainers, with no gap at the edges. Close the door. The blower door on many of these furnaces is part of the safety circuit. A door that is not latched can keep the blower from running, or it can let the blower run with the compartment open, which these listings do not want.
If you cannot find a pad at all, the furnace may have been running without one. That fills the blower wheel and the belly ducts with lint. A new filter does not clean a wheel that is already packed. If airflow is weak after a fresh pad, the wheel or a disconnected belly duct is the next thing to look at, and that is often a service call.
Florida, and the rest of the cooling season
In Florida the same closet unit is usually the air handler, and it runs for months. Check the pad monthly in cooling season. Replace it when you cannot see light through it. Humidity does not change the inches. A pad reinstalled wet, or a return blocked by a tight bedroom door, does. Do not prop open a fuel-burning compartment to “help the filter.” The water heater next door is a separate appliance.
Where to buy the pad
Hardware stores stock the pleated sizes site-built houses use. Manufactured-home suppliers stock the foam. Mobile Home Parts Store and Fulton MHP are two of them. Give them the model number and the measurements, not just “Coleman.”
Amazon listings exist for mobile home furnace foam filters. Read the dimensions on the listing and compare them to the pad you measured. Ignore a “fits Coleman and Nordyne” line that names both 7660-3401 and 669073 unless the inches match your door. A cheap pad of the right size is fine. A cheap pad of the wrong size is a hole in the filter.
Buy two once you know the size, and write the size on the closet door. That is the whole maintenance plan for this part.
Questions people ask
What size filter does a Coleman mobile home furnace use?
One Coleman/Evcon foam filter, part 7660-3401, is sold as 1/4 inch by 19 inches by 36 inches and is described as fitting a Presidential II furnace door. Other Coleman furnaces use other pads. Take the old filter out and measure it. Verify the size for your home.
What filter fits an Intertherm or Miller furnace?
A foam filter sold as Nordyne part 669073 is listed by one supplier as 16 by 26 inches for several Miller series, including CMF. An exploded diagram of a CMF furnace calls that filter F-10. The same badge was used for years, and the pad changed. Measure the one in the door.
Can I use a 1 inch pleated filter from the hardware store?
Only if the furnace was listed with a rack for that filter. The common door pad is a thin foam sheet. A dense pleated filter can choke a blower that was sized for a low-resistance pad. Follow the furnace manual. If a previous owner added a rack, watch for a furnace that overheats or short-cycles after you install a thicker filter.
How often should the filter be changed?
There is no single interval that fits every home. Check it monthly during the season you run the system hardest. Wash or replace a foam pad when light will not pass through it or the surface is packed with dust. If the manual states an interval, use that.
Sources
- 24 CFR 3280.707, heat producing appliances — eCFR
- Dean's Mobile Home Supply, filter part 669073 — Dean's Mobile Home Supply
- CMF series diagram listing filter 669073 as F-10 — Mobile Home Depot MI
- Coleman/Evcon foam filter 7660-3401, 1/4 by 19 by 36 — HSMHS
- Source 1 foam filter S1-7660-3401 — HVAC Parts Store
- Where furnace model numbers are often found — Mobile Home Parts Store newsletter