Floors · Problems

Fixing a soft floor near the bathroom

A soft manufactured-home floor by the bathroom is usually wet subfloor. Find the leak, see what the joists look like, and patch with plywood.

· About 8 min read

Symptom
The floor gives underfoot next to the tub, shower, or toilet
Timing
Fix soon

Repair the soft spot in the right order

Stop the water, see how far the damage goes, replace the bad decking and any soft joist wood, then close the floor.

  1. Find and stop the waterA new floor over an active leak will soften again. Check the toilet seal, the tub or shower, the supply lines, and the belly under that room.
  2. Open a small inspection holeSet a saw barely deeper than the subfloor. Look for pipes, wires, and ducts before you cut a full rectangle.
  3. Probe the joistsSurface stain can dry. Wood the screwdriver sinks into has to be sistered or replaced back to solid lumber. Several soft joists are a contractor job.
  4. Support every edge of the new panelLand the cut on joists or add blocking. The patch cannot float between joists.
  5. Install plywood, not particle boardMatch the thickness. Face grain perpendicular to the joists. Fasten with subfloor screws. Do not use drywall screws.
  6. Dry the cavity and fix the bellyWet insulation gets replaced. The belly wrap gets patched so the new insulation stays put. In humid weather, give the joists time to dry before you close them up.

A soft spot beside the toilet or along the tub is one of the most common repairs in a manufactured home, and it is almost always water. The floor feels spongy because the subfloor has lost its glue. Covering it with vinyl plank, or screwing a second sheet on top, hides the spot until the new floor flexes too. The repair starts with the leak, then the wood, then the finish.

Many of these homes were built with a particle-board subfloor. It stays flat while it is dry. Once it stays wet it swells, the resin lets go, and what is left behaves like wet cardboard. Some newer homes used plywood or OSB instead. You will not know which you have until you open the floor. Verify the material and the thickness for your home. Do not order a stack of plywood from a guess.

People say mobile home for the whole group. A home built before June 15, 1976 was a mobile home under the federal definition. One built on or after that date to the HUD Code is a manufactured home. Particle board shows up in both. The leak does not care which word is on the title.

Where the water usually comes from

The toilet is the usual start. A failed wax ring, a flange that rocks because the deck is gone, or a weeping supply line wets the particle board in a circle that then spreads. If the toilet rocks, the wood under the flange has quit.

The tub or shower is next: failed caulk, a cracked surround, a leaking drain, or a faucet dripping inside the wall. You often see nothing until the floor moves.

Look at supply lines with a dry towel. Gray plastic under older homes is sometimes polybutylene. Do not flex it to test it. Under the floor, torn belly paper, wet insulation, and a water heater drain that dumps underneath will wick up into the deck. Skirting with no vents makes a damp belly worse. Standing water is what rots the floor. A disconnected air-conditioner condensate line does the same job, quietly, all summer.

Stop using the wet fixture

If water is actively dripping, shut the supply to that fixture. For the toilet, the stop is usually on the wall or the floor beside the tank. Sponge the tank and bowl down before you pull the toilet, so you are not dumping a bowl of water into the hole you are about to inspect. If the smell is sewage, or the insulation below is black and wet with waste, stop. That is a health problem and a plumbing problem, and cutting it open without knowing where the line is broken is how the repair gets larger. Gloves and a plan, or a plumber who will open the floor, are the right next step. Do not tile over a sewage leak.

If you see scorched wiring, a warm spot on the floor that is not near a supply duct, or a breaker that trips when the bathroom is wet, stop and get an electrician. Water and the branch circuits under a bathroom are a bad pair. This page will not walk through electrical repairs.

Open the floor so you can see

Pull the finish floor back past the soft area, not just the worst square. The damage under particle board is usually wider than the spot that feels bad, because the water wicked.

Set a circular saw just deeper than the subfloor. If you do not know the thickness, pull a floor register or drill a small inspection hole and measure the edge. An extra eighth of an inch of blade depth is enough to get through. A deep plunge will find the supply line, the drain, or the wire someone stapled to the joist. Cut a hand hole first, about four inches square, and look with a light. Then mark a rectangle whose edges land on joists, or mark where you will add blocking.

Particle board that is still dry and solid can stay. Particle board that is swollen, crumbling, or dark and soft comes out. Bag it. It is heavy when wet, and it is not something to leave in the belly “for now.”

Joists, sistering, and the line you should not cross

Probe each joist. A stained face the screwdriver will not enter can dry. Wood the blade sinks into is decayed. Sistering means fastening a new board beside the old one, reaching solid wood past the rot, with structural screws or nails. Drywall screws snap. Hire the job out if you have not done that joint before.

Stop and hire a contractor who knows these floors if:

  • More than one joist is soft, or the rot runs past the middle of a span.
  • The room sags, doors in that area suddenly will not latch, or the tub has dropped.
  • You find crushed duct, a broken drain, or wiring laying in wet insulation.
  • You are not sure you can land the new panel on solid wood.

Manufactured-home floor joists are not always the 2x10s a site-built house uses, and the spacing is not always 16 inches. Measure the spacing and the joist size. Do not assume either one. A patch that misses the joist and relies on the finish floor to span the gap will feel soft again the first week.

The new panel

Match the thickness you removed. If it was 3/4 inch, use 3/4 inch. Ask for plywood stamped Exposure 1 or Exterior. APA describes Exposure 1 as a moisture-resistant bond for construction delays, not as a panel you leave out in the weather. Tell the yard the joist spacing and ask which span rating fits. Do not copy a thickness from another house.

Run the face grain across the joists. Put blocking under every edge that does not sit on a joist. Fasten with subfloor screws, not drywall screws. The toilet flange has to land on the new wood. If the flange is cracked or spins, repair it before a new wax ring. OSB can work if the stamp covers the span, and it also swells when wet. Next to a toilet, plywood is the more forgiving panel. Do not put particle board back down.

Dry the cavity, then the belly

Do not close wet joists the same afternoon, especially in Florida humidity. Fan the opening for a day or more. If the wood is still soft after it dries, it needed to be replaced. Compare a moisture-meter reading with a dry joist in the same home if you already own a meter. Do not trust a number copied from the internet.

Replace wet insulation. Patch the belly so the new insulation stays up. Mobile Home Parts Store and Fulton MHP sell belly tape. A ground vapor retarder helps when the soil is the source. It does not fix a toilet seal. Buy the plywood locally so you can read the stamp. Order the tape, the flange ring, and the wax ring once you know which flange you have. An online plywood search is a poor way to buy a sheet you need to inspect.

Put the fixture back, then the floor

Set the toilet only after the flange is solid. New seal, new bolts, and no rock. Do not caulk the base until you have filled the tank and watched for a drip. Caulk hides the leak you need to see.

Vinyl can go over a dry, fastened patch. It cannot go over the soft spot you started with. If the new panel is a different thickness, feather that. Do not stack scrap vinyl to make up the difference. If the spot returns in a month, the water was not stopped. Go back to the fixture and the belly before you buy another sheet.

Questions people ask

Why is the floor soft next to the toilet or tub?

Water reached the subfloor and stayed there. In many manufactured homes that subfloor is particle board, which swells and crumbles when it is wet. The usual sources are a toilet seal, a tub or shower leak, a supply line, or moisture from the belly underneath. The soft spot you feel is often smaller than the damage.

Can I screw a new layer of plywood over the soft spot?

No. A cap over rotten decking leaves the wet material and any soft joist in place, and the new floor will move as soon as someone steps on it. Cut out the damaged decking back to solid wood, support every edge, and then fasten a new panel.

What should I replace the subfloor with?

Plywood the same thickness as the panel you removed, stamped Exposure 1 or Exterior, with the face grain running across the joists. Exposure 1 uses exterior glue and is the usual subfloor panel. It still has to be covered and kept dry. Do not put particle board back down in a bathroom.

When should I stop and hire someone?

Hire a pro if more than one joist is soft, if the room is sagging, if you see sewage, if wiring is wet, or if you have not sistered a joist before and the screwdriver sinks into the wood. A small, dry, solid-joist patch is a reasonable owner project. A floor that is collapsing is not.

Sources

  1. 24 CFR 3280.709(h), water heater drip pan — eCFR
  2. 24 CFR 3285.505, crawlspace ventilation and drains — eCFR
  3. APA explanation of Exposure 1 plywood — APA – The Engineered Wood Association